By Lia Van Steenderen
В книге подробно описываются этапы изготовления несложных текстильных кукол и одежды для них.
Также можно использовать при пошиве одежды для детей до 7 лет
(если этим кто-то ещё в наше время занимается :)).
Read or Download Making Dolls and Dolls' clothes PDF
Best toys & models books
Книга камуфляж и маркировка бронетехники 2-й Новозеландской дивизии камуфляж и маркировка бронетехники 2-й Новозеландской дивизии Книги Вооружение Автор: Джефри Плоуман Формат: pdf Издат. :Модель центрум Прогрес Страниц: fifty six Размер: 40,45 Язык: Английский0 (голосов: zero) Оценка:В книгерассмотрен камуфляж и маркировка бронетехники 2-й Новозеландской дивизии в период 2-й Мировой войны .
This source for making teddy bears unearths easy methods to craft open-mouthed bears, sculpt enamel, create fur, make double-jointed necks and use trapunto and silk ribbon embroidered paw pads. There are styles for a normal teddy undergo, a latest one and one for a practical bruin.
As version railroaders all started hard ever-greater realism, Lionel spoke back in 2004 with its FasTrack method that includes an built-in roadbed, scale-sized ties, and a less-obvious middle rail. Veteran pastime writer Bob Schleicher follows up his The Lionel FasTrack ebook with a more in-depth, extra distinctive examine Lionel’s innovative O-gauge procedure.
I purchased this booklet a number of months in the past and feature knitted a couple of clothes and dressed up a few bears to provide as presents, that have thrilled the recipients. i don't examine myself a good knitter yet this ebook is comparatively effortless to stick with (and there's consistently YouTube to provide you a assisting hand - which was once necessary for provisional cast-on).
- Junkers Ju 88
- Fantastic Figures: Ideas and Techniques Using the New Clays
- F-16 Fighting Falcon (Models A&B)
- Verlinden's Showcase No. 3
- Knit This Doll! A Step-by-Step Guide to Knitting Your Own Customizable Amigurumi Doll
Extra resources for Making Dolls and Dolls' clothes
These were cut somewhat undersized to allow for expansion when I tidied up the edges using a square metal file. Also added to the base plate were some of the tank recovery parts shaved from the Tamiya kit. I also shaved the fuel strap ratchet buckles from the kit drums. These were set aside for attaching to some lead foil straps later on. Some of the KFOR Challengers I’ve seen did not carry the extra fuel tanks, so I decided to leave them empty with just the straps in place. The side armour was the next part of the hull to be detailed.
Instead of trying to cut the curve with an X-Acto, I outlined the shape on the plastic using a pencil and then removed the excess with a drum sander mounted in a Dremel tool. This method can quickly melt the plastic, so I hooked up a sewing machine pedal to my Dremel. This permits the machine to turn slower and not build sufficient heat to melt the styrene. My Dremel tool is a single-speed type; I have read that you should not attempt to hook up a speed controller to a Dremel with the five-speed selection as it can damage the motor.
There’s only two tricky bits to this part – getting the curved corners at the rear, and remembering that the lid has a gentle slope to the rear. I managed to build a complete bin before realizing this! 040in. sheet and used CA to hold it. That way, I could just sand a curved radius without fear of going right through the plastic. The top and bottom edge of the bin was trimmed with styrene rod and the sides detailed with some strips. 020in. rod; again I drilled a small hole in the C bracket and the base for the 45-degree supporting bar.
- Download The electrical engineering handbook. Systems, controls, by Richard C. Dorf PDF
- Download Microsoft Mapping: Geospatial Development with Bing Maps and by Ray Rischpater, Carmen Au PDF